I have unlocked my drive using my user password.
#Atapwd download password
when the entering master password you have to make sure its the correct one. Master password can be find in the internet. if the security level is high drive can be unlocked by using the HDD master password & user password. Note: if the security level is maximum drive only can unlock by using the user password. will shows the all partitions and the data that you have stored in the drive. in the passport panel, will shows in the security category is off. close the window and click the "passp" in main window.then click the "Unlock drive" then drive password will removed.in that window input the password that you have given to the HDD.then will open the security operation window. launch the Victoria after plug the HDD to the PC.To unlock the ATA HDD password, there is a easy way to do that. If your laptop does not support SATA hotplugging, then this trick will have to be performed on another computer - preferably a desktop, since desktops are usually more standards-compliant than laptops are.Īlso, the SATA controller must be set to AHCI for this to work. IF your laptop supports SATA hot-plugging (some don't), then your hard drive will become available and you can use hdparm to remove the password from the drive.Once the system has booted, reconnect the SATA cable to the hard drive.With the SATA cable disconnected, power the computer up and boot from the CD or flash drive you made in step 1.With the computer turned off, unhook the SATA cable from the affected hard drive.There are many tools and ISOs available on the Internet for this. Burn yourself a Linux Live CD or make a bootable Linux USB flash drive.It depends on whether or not the USB controller in the enclosure will reject the commands. Issuing ATA commands to a SATA drive in a USB enclosure may fail.
![atapwd download atapwd download](https://pic.filecast.co.kr/00/16/00165fb42e28ddd73c06aba71d858695.png)
Please note, a USB enclosure may not work. That means if you can get around the BIOS, you can access the drive. Fortunately, the ATA security spec is only enforced by the BIOS, not the drive itself.
![atapwd download atapwd download](https://www.xbox-hq.com/html/files/modding_with_r-clone_2.jpg)
I was hoping that could somehow erase hdd without passwords.This is a "feature" of many BIOS implementations.
#Atapwd download download
If level security MAX, need to know the master password too. Hirens Boot CD 15.2, Dos/Windows/Linux Bootable CD, Hirens BootCD, Download WinTools, Partition/Data Recovery. (High)For "hdparm" command, need to know the master password. I suggest you firstly looking in what mode (High/Max) is locked your drive, and if master pass is modified or not, with this hdparm command: The SECURITY ERASE UNIT command requires the Master password and will completely erase all data on the disk. In Maximum security mode, you cannot unlock the disk! The only way to get the disk back to a usable state is to issue the SECURITY ERASE PREPARE command, immediately followed by SECURITY ERASE UNIT. There is an attempt limit, normally set to 5, after which you must power cycle or hard-reset the disk before you can attempt again. In High security mode, you can unlock the disk with either the user or master password, using the "SECURITY UNLOCK DEVICE" ATA command. Bit 8 in word 128 of the IDENTIFY response tell you which mode your disk is in: 0 = High, 1 = Maximum. A value of 0xFFFE means the Master password is unchanged.Ī disk can be locked in two modes: High security mode or Maximum security mode.
![atapwd download atapwd download](http://4.bp.blogspot.com/-bVOGjKYxZ8I/Ue_B2D-vNlI/AAAAAAAAELc/we4aI1fcjIs/s1600/2qn0bdj.jpg)
#Atapwd download code
The revision code is word 92 in the IDENTIFY response. Most disks support a Master assword Revision Code, which can tell you if the Master password has been changed, or it it still the factory default. It is part of the ATA specification, and thus not specific to any brand or device.Ī disk always has two passwords: A User password and a Master password. The disk lock is a built-in security feature in the disk. If the above suggestions don't work, here's some background info about the disk lock feature: Shut down the computer and remove the disk. For WD, The password id "WDCWDCWDCWDCWDCWDCWDCWDCWDCWDCW"Ĩ. For Toshiba and Hitachi disks, if the above doesn't work: Choose "unlock with master password", then "disable with master password". The password is empty, so just press enter at the prompt.Ħ. For Fujitsu disks: Choose "unlock with user password", then "disable with user password". Select the locked harddrive and press enter for the menuĥ. Create a bootable DOS disk, and put atapwd.exe on itĤ. Download the tool "atapwd.zip" (written by Alex Mina)Ģ.